L-Acoustics LLC-115b-2w (new)

L-Acoustics LLC-115b-2w (new)

New Arrival Ask about this item

 300

Choose your currency:

Price is excluding VAT

3 Available

LLC115b-2w
L-Acoustics LLC-115b-2w (new)

 300

The L-ACOUSTICS LLC 115b-st or LLC 115b-2w line level controllers are analog signal processing units that optimize the performance of the MTD115b loudspeaker when used in passive or active mode, respectively. For stereo operation of passive MTD115b enclosures, the LLC 115b-st accepts two signal inputs and provides two processed outputs for the respective input channels plus a filtered, summed output for subwoofer drive.

SKU: 11053 Category: Tags: , , , Brand: L-AcousticsMPN: LLC-115b-2wEAN: 7333293110532Condition: UsedCondition Description: New and unusedWarranty: 72 hoursPackaging: Original boxTariff (HS-Code): 8543 70 90 99Location: Sweden

Share:

The LLC 115b-2w is for mono operation of active MTD115b enclosures and accepts a single signal input while providing processed outputs for the subwoofer, low and high frequency channels. The main functions of the LLC 115b-st and LLC 115b-2w controllers are as follows:

  • Bandpass filtering and equalization (3 modes, selectable)
  • Crossover filtering for low and high channels (LLC 115b-2w only)
  • Mono summation for subwoofer drive (LLC 115b-st only)
  • Crossover filtering, equalization for subwoofer drive (3 models, switch-selectable)
  • Sense Return processing for thermal protection of speaker components and cone excursion limiting (voltage and frequency dependent)

Three different equalization/bandpass filtering modes tailor the frequency response of the MTD115b to suit different applications (selected via front panel switch). In MONITOR mode, high pass filtering is set at 45 Hz and a modest low frequency shelf is applied to provide an equalization contour suitable for floor monitor applications. In FRONT mode, a 45 Hz high pass filter is employed and increased low frequency shelving provides an equalization contour that is more suitable for FOH use. In X- OVER mode, a 100 Hz high pass filter is applied since the MTD115b is intended to be used with additional subwoofers.

For subwoofer drive, the second front panel switch allows for selection of bandpass filtering and equalization that is optimized for either SB115, SB118 or SB218 subwoofers. The processed subwoofer signal output is then available on the XLR connectors provided on the front or rear panels of the controller.

Note: The SB118 setting should be employed when using the LLC 115b-st or LLC 115b-2w controller for dV- SUB processing (bandpass filtering and equalization are compatible)

For the LLC 115b-st, two input signals (Ch A, B) are applied to the line input XLR connectors on the front panel of the controller. Rear panel XLR line outputs (Ch A, B) are connected to the power amplifier inputs with the amplifier outputs then connected to the controller “Sense Return” input Speakon connector (Ch A = 1+/1-, Ch B = 2+/2-). Since the amplifier is connected in a loop, LLC sense return protection circuitry can monitor the signal applied to the loudspeakers and provide thermal protection of speaker components plus voltage- and frequency-dependent cone excursion limiting provided that the power amplifier has 32 dB gain. The front panel of the LLC 115b-st is then used as a patch panel with Ch A, B loudspeakers connected via the two 4-pin Speakon connectors provided.

For the LLC 115b-2w controller, a single input signal is applied to the line input XLR on the front panel. Rear panel LF and HF XLR outputs are connected to power amplifier input channels with the amplifier outputs then connected to the controller “Sense Return” input speakon connector (LF = 1+/1-, HF = 2+/2-). As for the LLC 115b-st, protection circuitry monitors the signal applied to the loudspeakers to provide thermal protection of speaker components plus voltage- and frequency- dependent cone excursion limiting provided that the power amplifier has 32 dB gain. The front panel of the LLC 115b-2w is then used as a patch panel with loudspeaker connection via the 4-pin Speakon connector provided.